Maytag centennial washer not spinning clothes dry

This washer is designed to use the Bulky or Sheets/Bedding cycle for bulky clothing items or bedding. When washing these types of clothing items (including heavy coats or blankets), do not use the Normal cycle or a Rapid Wash cycle (on some models). Clothing performance may not be ideal if using these cycles. 

Was there a power failure?

If the power failed during the spin cycle, it's possible the washer did not ramp-up to full spin speed.  

Did you receive an error code?

Click the Troubleshooting option above for Error Codes

Did you use the "Add a Garment" feature?

Only add clothing items while the "Add a Garment" indicator light is on. Pausing the machine later in the cycle could cause limitations on the washer running at maximum spin speeds. When Add Garment is lit, you may pause the cycle, open the lid, and add items. Touch and hold the START/PAUSE button to start the cycle again.

Is water standing in the tub?

Check drain hose for proper installation.  Use the U-shaped drain hose form on the drain hose and securely attach to drainpipe (standpipe) or tub.  Check that only 4.5" (113 mm) of the drain hose is in the drainpipe (standpipe).  Do not tape over the drain opening. 

The drainpipe (standpipe) height requirements are 96" (244 cm) maximum and 39" (99 cm) minimum.  Your washer will not be able to adequately pump the water out of the appliance if the drainpipe (standpipe) exceeds 96" (244 cm).  In this case, the water may flow back into the washer. 

Make sure the drain hose is not kinked or clogged.  Straighten the hose for adequate water flow.  Remove any blockage from the drainpipe of the utility sink.   

CLICK HERE for more information on drain hose installation.

Is the load unbalanced or overloaded?

The wash load must be balanced and not tightly packed. A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle.

CLICK HERE for more information on loading your washer

Is your washer level?

The washer must be level.  If not, the load may become unbalanced, causing the machine not to spin correctly.  This can also cause the washer to have excessive noise and/or vibration, especially during the Spin cycle. 

CLICK HERE for more information on leveling your washer

Was Low Spin or No Spin selected?

Cycles with lower spin speeds remove less water than cycles with high spin speeds. Use the recommended cycle/speed spin for your garment.

To remove extra water in the load, select Drain & Spin. The load may need to be rearranged to allow even distribution of the load in the basket.

If Low Spin or No Spin was selected, the washer might not remove enough water from the load.

Still need help? Contact us or schedule service.

Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.

United States

Schedule Service Online

Contact Us

Canada

Schedule Service Online

Contact Us

Interested in purchasing an Extended Service Plan?

Please click below to learn more on how you can save up to 25% on New Appliance Extended Service Plans within 30 days of your appliance purchase.

Some homes, it appears, are having issues with top-load washing machine spins. It is not just Maytag; any reputable company’s washer can be affected.

It is distressing to see the Maytag Centennial washer not spinning or draining. However, most of the time, there is a simple solution. It is unlikely that you will have to go all the way to fix an issue.

This troubleshooting article will show you precisely what you should do to fix your washer’s spinning issue.

If your Maytag Centennial washer would not spin, here’s what you should do.

The very first step is to remain calm and take a deep breath. For such minor issues, many do not avoid this washer type.

Also, do not worry about sopping wet clothes for the time being. All will turn out beautifully.

It would be best if you started with a straightforward inspection (which is where most folks find the answer). You will slowly progress to more tough sections. Fix the spin difficulties by following these troubleshooting steps:

Excessive Load

Your Maytag Centennial washer would not spin because of the additional workload. You have probably seen it before: stuck laundry may render any washer inoperable. This is the most prevalent reason for that specific issue.

Extra-large clothing will accumulate on one side of the drum, causing a slew of issues. Outside the drum, there can be tangled garments as well.

Begin the spin cycle again after removing some garments from the drum and outside the drum.

If that does not work, move on to the next step.

The Connection On The Motor Is Broken

It links the motor and gearbox, and it is through this connection, that the washing drum receives power. So, if it is faulty or fails in some way, your washer’s spin cycle will not work.

If the washer is subjected to severe loads regularly, the power connection may cease to operate and be seriously affected. You must replace it if it is damaged.

Drain Hose Blocked

The drain hose will not spin or wash if it is plugged. Remove the drain pipe from the backside of the washer to make sure. To ensure the hose is not blocked, run water through it.

This is also an excellent opportunity to inspect the washer’s drainage. This is also a perfect opportunity to review the washer’s drain. If you have hard water, limestone build-up might block the drain. Make sure there is not anything caught in there.

Lid Switch Failure

Your washer will not spin your soaked items to dry if the cover is open. As a result, it is an excellent moment to inspect the lid switch. Its purpose is to keep the washer from whirling if the lid is left open.

You can check the plastic button on the lid (which activates the lid switch when the top is closed) for any wear and tear.

When there is no visible damage, you may have a problem with the lid switch.

When shutting the lid, listen for a click.

If you do not hear a click, the lid switch is most likely faulty and must be replaced by a specialist.

Problems With The Drive Belt

Your Maytag washer will not spin if the drive belt is faulty, damaged, or just loose. When it turns and produces a loud noise, you should look into it.

Make that the drive belt is attached to the lever system. To do so, you must first find it. Remove the rear panel of your washer to find it.

Adjust the drive belt on the rollers if it appears to be loose. However, if it is damaged or broken, you must restore it.

A Clutch That Has Seen Better Days

If your washer’s clutch is broken down, it will not spin. The clutch component connects the internal tub to the gearbox, raising its spin speed steadily.

If it becomes worn out, it will stop spinning. The worn-out clutch is beyond repair. It would be best if you replaced it.

On The Rotor, There Are Damaged Magnets

The rotor generates a powerful electromagnetic field that interacts with the rotor to spin the tub. However, if the rotor magnets are destroyed, the washer will not cause trouble or spin.

The faulty magnets, like the worn-out clutches, are irreparable. So, if the rotor is broken after evaluation, you must replace it.

A System With A Faulty Bearing

The washer’s rear drum features springs that allow the internal tub to spin freely. If your Maytag Washer is stuck in the spin cycle, that’s where you must look. It will also become extremely noisy as a result of the damaged bearing.

As a result, you must act quickly to rectify the situation. The hinges can be purchased separately. However, we recommend purchasing the replacement drum and bearing as a package.

Transmission That Is Worn Out

The washer transmission is made up of its parts. The washing machine may not spin if such failures occur. Although highly unusual, the powertrain may become damaged or worn out over time.

Only replace the transmission after thoroughly inspecting all other parts. Also, get expert advice before deciding this.

Life Expectancy Of Maytag Washers

The average lifespan of a new washing machine is 11 years. If the machine is more than eight years old and is a high-end brand, Consumers Reports advises against replacing it.

How To Fix Your Washing Machine

It could be as basic as altering detergents, adjusting a hose, or leveling the machine if your washer is not functioning right. Some troubles will necessitate professional guidance, so it is critical to understand what you can do yourself and require a service call.

Our article will assist you in repairing your washing machine for various situations.

If you have a front-load washer, a clogged drain pump filter is likely to be the source of the troubles stated below, such as draining, spinning, and stench. To begin, clear the outlet pump filter of any dirt or lint, as well as any remaining water.

If you have a Maytag® washer, check your Owner’s Manual for model-specific cleaning recommendations or use Maytag Product Help. If washing the drain pump filter does not solve the problem, continue reading more troubleshooting advice.

The Washer Refuses To Drain

You may also have a twist or clog in the drain hose, a drainage pipe that is too lengthy, or a slow-spin choice enabled if your washing machine will not drain or your clothes are coming out too moist.

Was A Slow Spin Speed Or A Gentle, Delicate Cycle Chosen?

Slow spins are used in gentle, delicate, and wash and dry cycles to keep materials from stretching and wrinkling. Slow spinning also adds to the amount of water in the load. Choose a cycle with high spin speeds, such as the Normal cycle, to drain more water.

Is Your Washing Machine Unlevel?

The washer must be leveled. If you don’t, the load can also become imbalanced, preventing the washer from spinning effectively. Severe noise and vibration can also result, particularly during the spin cycle.

The Washing Machine Is Breaking Down

The washer is designed to keep water in it. However, if you notice moisture on the floor, there may be a simple solution. Wipe down the drain pump filter, adjust the hose attachments, and clean the door seal.

Gurgling And Humming

It is typical to hear a continual humming sound from the pump or motor while the loads are being washed and intermittent gurgling or surging as water is withdrawn during the spin or drain cycles. After you begin the washer, you may hear the humming of the sensor spins.

Every 30 Washes, Clean Your Washer

Your washer may feature a cleaning cycle or even a cleaner that is suggested. Maytag recommends Affresh® washing machine cleaner tablets, but you can also use everyday household products.

Quick Remove Loads After The Cycle

Leaving loads in the washer for too long can result in unwanted odors. Switch loads to the dryer as soon as possible, or use a cycle like Maytag’s Fresh Hold® option, which maintains to agitate loads after they have been washed.

In Laundry Loads, Use Less Detergent

Many consumers use too much detergent, which can lead to overdosing, leaving a deposit, and generating odors. You need to fill the detergent cap up with the first line for a standard load, around a spoonful of detergent if you’re using the detergent cap to quantify. You could use up to ten times the amount of detergent you need if you fill-up the entire lid.

Wash & Dry Cycle Overnight

Do you want your clothes washed and dried, but you are too lazy to wait for them to complete washing before putting them in the dryer? Your clothes may now be washed and dried in one washer and be ready for you in the morning with the Maytag Overnight Wash & Dry Cycle!

Your garments will continue to tumble after the wash cycle is over as air passes through the load.

Cycle Of Sanitization

Most people are unaware that cleaning their garments in the washing machine does not necessarily ensure that they are completely clean. It is difficult to guarantee that all of your garments will be fully germ-free if you use cold water, a shorter cycle, or do not use chlorine.

Why is my washer not spinning clothes dry?

What causes a Maytag Centennial washer not to spin?

How do I reset my Maytag washer that won't spin?

Why is my Maytag washer leaving my clothes wet?