This guide will give you step-by-step instructions on how to replace the water filter in your Whirlpool refrigerator. It’s recommended that you replace your water filter every six months. If you don’t, you risk the water starting to taste bad, odors emitting from your fridge, and leaks occurring in your fridge. Show Before you can replace your water filter, make sure you purchase the correct replacement filter from a retailer that stocks them. On your existing water filter, there should be a product code that you can use when ordering replacement filters. As soon as you have the correct replacement filter, you can follow the steps in this guide to remove and then install the new filter into your Whirlpool refrigerator. This guide covers all major Whirlpool refrigerator models, including:1ET25DKXGW00 2-A Y 3EAD19XMWR1 3ECKMF10 3ECKMF8 3ECKMF86 ED5FVGXWS07 WRB322DMBM00 WRF535SMBM00 WRF560SEHZ00 WRF560SEYM05 WRF736SDAM11 WRF736SDAM12 WRF736SDAM13 WRF736SDAM14 WRS322FDAM04 WRS325FDAM02 WRS325FDAM04 WRS571CIDM01 WRS571CIHZ01 WRX735SDBM00 Step 1 – Get preparedThe first task is to locate your water filter. Depending on your exact Whirlpool refrigerator model, it will either be in the grill that’s at the base of the fridge or inside the refrigerator at the back. You should be able to easily find it, but if you’re not sure, you can always check your user manual. Once you’ve located the water filter, it’s a good idea to place a towel down underneath the filter unit to pick up any water that leaks out when you remove the old filter. You can also turn the ice maker off as this can be another source of leaking water. If you have an older Whirlpool refrigerator, you may also need to turn the water supply off manually—but usually, there is an automatic water valve that ensures no water leaks out when you change the filter. If you’re not sure if you have an automatic water valve, you should check your user manual. Step 2 – Remove the old filterNow that you’re prepared, you can remove the old filter from your fridge. The easiest way to do this is to:
Step 3 – Install the new filterNow that the old water filter has been removed from your Whirlpool refrigerator, the next step is to install the new one. You can do this by:
Step 4 – Flush the water pipe outNow that the new water filter has been installed into your Whirlpool fridge, it’s a good idea to flush the system out before you start drinking any water or making ice with it. This is especially important if your filter hasn’t been changed for a while. To flush the water pipe out, place a 1-gallon jug under the dispenser and dispense four jugs worth of water (4 gallons) out of the tap and pour it down the sink. Once flushed out you can start to drink water from your fridge again. Remember to change your filter every six months to avoid any problems from occurring. When you own a refrigerator that makes ice and puts out cold water, you will need to change the filter every six months to keep your water tasting fresh. Today we are going to explain how to change the water filter on a Whirlpool WRS325SDHZ refrigerator. The filter you will need to have is an EveryDrop 10383251.
Finding where your refrigerator should be very easy – most refrigerators have a water line that runs through the cabinets to below the sink. Once you locate the source, there should be a valve. Turn the valve clockwise until it won’t turn anymore. 2. Drain the Water from the Refrigerator Using a pitcher or large glass, drain the water from the cup filler on the front of the refrigerator. Make sure you drain all the water from your refrigerator so you won’t have any leaking when you remove the filter. 3. Remove Water Filter The water filter will be located inside the refrigerator, at the top left of the refrigerator part. Flip down the cover; you will see an arrow on the cap pointing to the right. Turn it counter-clockwise until the arrow is pointing up. The filter should slide right out. After the filter is removed, make sure you take the cap off of the old filter and then dispose of the used filter properly. 4. Install New Filter Click cap onto the new filter. Insert new filter with the arrow pointing up; then turn the filter clockwise until you hear a click. The arrow should be pointing to the right. 5. Finish Once you have the new filter installed, turn the water back on. Then you will need to “bleed” the line. Run the water for five minutes to ensure there is no air left in the line. Once that is done, you should be all set! If the filter light hasn’t reset, just press and hold the filter button on the front of the freezer door. And if you need help with anything, repairs, troubleshooting, etc., contact us! We at Jerry’s Appliance Repair have professional repair techs who are ready to come help you with anything you need. Does a Whirlpool refrigerator have a water filter?Whirlpool refrigerator water filters can be found either in the upper right-hand corner of the refrigerator's interior or behind the base grille. Some filters are twist-in models, while others are push-in.
Where is refrigerator water filter located?The majority of refrigerator filters are located in one of two locations: in the grille at the base of the fridge or in the back upper-right corner of the interior. In either location, you'll see a knob or a button that will release the filter for removal.
|